Autodesk HSMWorks Ultimate 2026 x64 + активация

Milling Toolpaths
-Engrave toolpaths can now be generated over multiple levels in cases where, due to tool geometry, the initial engrave toolpath had to be offset
-Fixed an issue in which Order Optimization was not working in 2D Pocket strategies.
-Fixed an Internal CAM Kernel error that the 3D Horizontal strategy was returning when predrill points were selected.
-Fixed a crash that could occur in a Parallel operation if a rest tool generated no machining boundary.
-Fixed an issue in which a linking move between Contour toolpath cutting moves could gouge through the model.
-Fixed an issue for certain profiling toolpaths where the tool was not cutting as much material as it should
-Fixed an issue in which a protected toolpath was not re-calculating after a tool change.
-Fixed some issues with Preserve Order for the Pocket strategy.
-Fixed a problem that could have caused vertical spikes to appear in the toolpath when the filleting option was used.

Drilling
-The "Probe" drilling cycle has been renamed to "Custom" to better reflect that this is a mechanism that can be used in conjunction with a post-processor that has custom logic for handling a non-standard cycle.

Post Process
-The library of installed posts has been updated with the latest changes
-Added support in the Post Processor kernel for head configurations and offset table configurations when TCP is not supported.
-Fixed an issue where the machine home position was not being output to the NC Code.

Templates
-Fixed an issue in which storing multiple operations in one template did not default to storing them in the correct location.

API
-Fixed an issue in which the Tool info was not updated when parameters were changed via the API.

Documentation
-Help content has been updated.

SolidWorks 2020
-This version of HSMWorks enables running with SolidWorks 2020. Note: Limited testing has been done with the pre-release, but not with the final release.

New in this Version:

-When there is more than one body in the model, no automatic selection of all the bodies will be done when creating a new Setup. (#8140)
-Added the ability for a grooving tool to go a specified distance below the inner radius while facing the part in a groove turning operation. (#11148)
-Fixed a problem with the retract at the shifted position when expanding the Fine Boring cycle for the post processor. (#11350)
-Avoid creating an extra tool entry when creating a new tool. (#11944)
-Added a new parameter "make sharp corners" to a profile turning toolpath to ensure that outside corners are sharp and not rounded. (#12010)
-Fixed an issue for Turning Profile operations in which leads were not generated at an angle with respect to the toolpath direction when "Use Fixed Lead Direction" was turned off. The problem occurred in both roughing and finishing passes. (#9944, #10284)
-Fixed excessive tool library load time with Harvey tools installed. (#11587)

Changes to toolpath generation:
-For the Engrave toolpath, improved the ordering to reduce the distance which the tool jumps when moving between letters in engraved text. (#4968)
-Fixed a problem in the Pocket strategy that could cause an operation to freeze and not finish. (#10484)
-Fixed an issue with the Turning Profile and Turning Groove operations where the tool was not cutting to the inner radius if there was a hole with a diameter greater than the inner radius. (#9921, #10106)
-Fixed an issue where gouge checking for Turning Profile leads was incorrectly being done for the tool nose center instead of the tool contact point. (#11298)

Changes to API:
-Fixed missing update of parameters when using HSMWorks_setObjectToolById().
-Added advanced API HSMWorks_setObjectGeometry2() to allow geometry override entity flags to be set.

The following changes have been made in the current update (2019.1):

New Features
- Major update of stock simulation to address various potential issues. (#9366)
- Added backplot feature in NC editor.
Changes
- Fixed issue where toolpath generation could fail when using rest machining. (#7811)
- Fixed wrong machining area issue for 2D Adaptive Clearing. (#9821)
- Fixed wrong default stock contours when using Cylindrical/Tube stock. (#10435)
- Fixed missing motion when simulating multi-axis toolpath for stock simulation in Fast 3D mode. (#10438)
Changes to toolpath generation
- Fixed wrong toolpath issue for turning. (#9917)
- Fixed potential generation failure when using negative stock to leave for turning. (#9722)
- Fixed wrong toolpath issue for turning. (#9751)
- Improved toolpath quality to avoid tiny moves for 2D Contour. (#7585)
Changes to post processor
- Major update of Mazak Integrex post.
- Major update of Siemens mill-turn post.
- Added power setting for through cutting, etching, and vaporize for Grbl laser post.
- Added support for rigid/non-rigid tapping for posts.
- Added support for M960 for controlling C-axis direction for Okuma LB3000 with OSP-300 control post.
- Added support for Spindle Speed Variation (SSV) for HAAS mill-turn posts.
- Updated coolant and retract handling for posts.
- Added support for DPM feedrates for multi-axis motion for Doosan mill-turn post.
- Added support for polylines and full circles for DXF post.
- Added support for tool calls by tool description rather than tool number for Siemens 810D post.
- Added property to control C-axis scale for DMS Router FAGOR posts.
- Fixed missing G43 when using the safe start all operations feature for HAAS posts.
- Fixed Euler angles for multi-axis positioning for posts.
- Fixed Z-probing clearance for Siemens 840D post.
- Fixed left handed tapping for HAAS turning post.
- Fixed missing spindle output for posts.
- Fixed missing force of G-codes at new subprograms for Siemens 840D post.
- Fixed missing force of G-codes at new subprograms for Robodrill post.
- Fixed missing force of G-codes at new subprograms for posts.
- Fixed tapping feedrate rounding issue for HAAS mill-turn posts.
- Fixed tapping feedrate rounding issue for HAAS turning post.
- Fixed tapping feedrate rounding issue for HAAS posts.
- Fixed tapping pitch property description for posts.
- Avoid machine retract at start of program for MaslowCNC post.
- Fixed failing ISEL post.
- Fixed inverse time/DPM output for rapid moves for Doosan mill-turn post.
- Avoid Z repositioning after a tool change for posts.
- Fixed machine axis support for HURCO post.
- Fixed multi-axis indexing issue for Tormach post.
- Fixed multi-axis indexing issue for Pocket NC post.
- Fixed missing RAPTO output for drill cycles for CAMplete post.
- Fixed output of C-axis when turning for Doosan mill-turn Fanuc post.
- Fixed issue where post processor could run out of memory. (#3115)
- Updated rotary positioning handling for posts.
- The spindle speed is now output using RPM mode prior to the first positioning and is then output in SFM mode when using 'Use constant surface speed' to avoid starting with a slow RPM for lathe posts.
- The spindle speed is now output using RPM mode prior to the first positioning and is then output in SFM mode when using 'Use constant surface speed' to avoid starting with a slow RPM for HAAS mill-turn posts.
- The spindle speed is now output using RPM mode prior to the first positioning and is then output in SFM mode when using 'Use constant surface speed' to avoid starting with a slow RPM for HAAS mill-turn post.
- Updated tapping feedrate for HAAS mill-turn posts.
- Added diameter and length registers at tool change for ACU-RITE MILLPWR G2 post.
- Updated coolant for Heidenhain posts.
- Updated circular motion handling for DXF post.
- Updated inverse time/DPM support for posts.
- Avoid empty blocks for Opticut post.
- Updated coolant and retract handling for posts.
- Changed C-reset to use closest virtual C0 instead of absolute C0 for DMS Router posts.
- Added check for tool break control for DMG MORI NHX and CMX posts.
- Time output is no longer forced for DATRON posts.
- Increased minimum chord length for posts.
- Added more decimals for feedrate for HAAS mill-turn posts.
- Updated multi-axis indexing for Siemens posts.

This release contains a number of important fixes and improvements, as identified below.

The following changes have been made in the current update (2018.3):

- Added support for pecking for Turning Profile. You can use this feature to break the chips.
- Added support for back cutting (used for Sandvik PrimeTurning) for Turning Profile.
- Added support for both ways Adaptive Clearing. When both ways is enabled you can set a separate load and feedrate for the opposite cutting direction. You can use this feature to reduce machining time further when roughing depending on the material you are machining. The main cutting direction (normally Climb) will be the preferred cutting direction but the opposite direction will be used when the alternative non-engaging stay down linking would be estimated to be longer.
- Fixed issue when selecting a tool from different operation in the tool library did not use the desired feedrates and speeds. #9235
- Fixed issue where pasted operations would not be marked as out-of-date when pasting into a different job. #8103
- Fixed issue where the maximum spindle speed would be overwritten when selecting tool which uses constant surface speed. #8394
- Show live tool setting for the Drill operation for mill-turn. #7934
- Show number of holes being machined for Drill. #8222
- Improved stock simulation of simultaneous multi-axis toolpath. #9187

This release contains a number of important fixes and improvements, as identified below.

Fixed issue with folder selection dialog. #8770
Avoid showing Maximum Groove Stepdown and Grooving Pattern when roughing passes are disabled for Turning Profile Groove. #8711
Fixed support for post processing to files that do not have a file extension. #8722
Corrected tooltip graphics for Contact Point Boundary parameter. #2492
Fixed incorrect default for Probe WCS Offset when creating new job. #8599
Ensure release of HSMWorks license when unloading addin. #8630
Reenable display of file name in post process dialog. #8784
Changes in toolpath generation:
Fixed wrong roughing toolpath issue for Turning Groove.. #8511
Changes to post processor:
Fixed missing unit mapping for Section.getParameter() API for number parameters. #8724
Fixed missing properties for CurveEntity API. #8766
Fixed error during cycle time calculation when there is a Z-plane probing cycle. #8551
Fixed issue with unsupported tool orientation for machine when post processing. #8772
Changes to post library:
Fixed wrong syntax for canned cycles for XML post.
Fixed missing indexing of C-axis in XCZ mode for HAAS mill-turn posts.
Fixed missing option for G18 property for Milltronics post.
Fixed homing of the C-axis at the end of the program and disabled the output of G80 after a part transfer operation for Doosan mill-turn Fanuc post.
Fixed helical move issues for MillPlus post.
Fixed probing cycles for Heidenhain posts.
Fixed helical move issues for Siemens mill posts.
Fixed wrong coolant M-codes for CNC Router Parts (Mach3Mill) post.
Fixed tapping with chip breaking for UCCNC posts.
Fixed issue with missing wrap of listed tools for HTML setup sheets.
DATRON MCR English/German posts are now deprecated. Use the DATRON MCR post instead.
Adjusted parameter output to exclusively use type attribute for differentiating between types for XML post.
Switched from using G53 to G28 for machine retracts for TinyG post.
Updated multi-axis rewind handling to allow for resetting of the encoder and handling of continuous axes for HAAS posts.
Added documentation of properties for HAAS posts.
Updated multi-axis rewind handling to allow for resetting of the encoder and handling of continuous axes.
Major update of DATRON next post with improvements and fixes.
Major update of DATRON MCR post with improvements and fixes.
Added Mazak laser post.
Added feedrate support for Mach3 waterjet post.
Added property to use pitch for tapping for Mazatrol Fusion 640M post.
Added documentation of properties for HAAS mill-turn posts.
Added support for BC-style trunnion for HAAS Next Generation posts.
Added support for 5-axis trunnion, subprograms, probing, nano smoothing, and center part at door for Doosan VMC Fanuc post.
Added new property ‘TCPType’ to control the TCP type for OSAI post.
Added property ‘useG0’ to turn on/off G0 rapid moves for Pocket NC post.