BurnInTest Professional 9.2 Build 1009 + Portable + Repack

Fixed an issue preventing AMD GPU temperatures from being read if ADL_Graphics_Platform_Get failed to be loaded from the ADL library
Fixed an issue reading AMD 4600/4800 CPU temps
Fixed an issue with the parallel port test not being able to get the port address and left unable to start the test in some cases

RAM Test, made some changes to avoid a verification error being logged when the system was low on memory, in some cases a write phase was aborted due to the low memory but the verification phase would continue instead of being skipped which would lead to a verification error for some patterns. This would only occur on systems that had nearly no free RAM before the start of the RAM test. So typically only on systems with <4GB of RAM installed and only when background tasks, other than the RAM test, were already using a lot of the available RAM.
RAM Test, made some changes when allocating/deallocating memory for the test in low memory situations, fixing a potential bug that could cause verification errors when small amounts of RAM (<100 MB) were being allocated/deallocated rapidly by the test when the system was low on memory. There isn't much point running the RAM test when you only have less than 100MB of free RAM, but if you do the error case is now handled better.
RAM Test, made some changes so multiple copies of BurnInTest running the RAM test will have separate shared memory blocks, still not recommended to run multiple copies of BurnInTest at the same time however.
3D Test, DX12, added a check before the DX12 executable is launched if the system is going to Suspend/Hibernate and wait until system is resumed, this should prevent an error being thrown if the test stats at the same time as the system is going to sleep (seen when rapidly sleeping/resuming system in a loop)

Audio loopback test, now supports PassMark Loopback Audio Plug
Audio loopback test, fixed an issue with the audio loopback test where if the test run time selected was 0 (run forever) then then sound playback time was too low (~1 second) instead of the expected 20 seconds.
RAM test, fixed a bug where the RAM test may only allocate 200MB of RAM for testing when run at 50% or lower duty cycle
Fixed monitor numbers in log files starting at 0 to now start at 1
Added GPU name used for each DX12 test to log

Fixed an issue when reading temperatures from AMD CPUs
Fixed an issue when reading temperatures from some NVMe disks
Fixed a UI issue where if the RAM test logged an error it might not be displayed on the dashboard until the test finished
Fixed an issue where disks weren't automatically selected when run in conjunction with minimising system info collection command line flag (-w) and the auto select disks preference setting
Disk test, fixed an issue where disks numbers being tested >80 might not show up in the log correctly
Added a new information log message when memory is very low when trying to run the RAM test
RAM Test, updated a trace log message when low memory is <50MB to be more clear about what is being logged
Added initial support for reading temperatures from Intel 11th gen CPUs

Disk test, forced destruction of any partition information and get system to update partition information when running a physical disk test, this prevent an access denied error when trying to test some physical drives that had partition information but the volumes weren't mounted
Temperature graph, redrawn at end of test to display all samples
Changed system information tab to show battery current charge, design and full charge capacity
Made some changes to the installer so BurnInTest won't launch after a silent install
USB Test, fixed an issue with the scripting command 'USB3CONNECTION' which was not setting the chosen speed correctly for 12 or 5000
USB Test, fixed a bug where USB threads were forced to stop if any plug was failing to be enumerated
USB Test, fixed a case where a USB error may not be thrown at test start under some circumstances where the plug was being forced into a particular test speed (eg USB3 plug on a connection with USB2 lines disconnected).

Fixed an inconsistency between BurnInTest and the DirectIo driver that was causing the parallel port test to fail
Added NOTEMP command line flag to disable temperature collection
Advanced network test, fixed a bug where a "connection reset by peer error" could occur when trying to test 4 or more network cards
Advanced network test, endpoint, fixed some possible crashes when memory failed to allocate
Fixed a possible crash when gathering SMART information from hard drives
Decreased a timeout value when collecting SMART disk information that could cause the temperature initialising and collection to free or time out when some USB drives were attached to the system under test.

Fixed "Display errors by categories" checkbox being hidden on high DPI settings
Updated system information library with initial support for AMD Ryzen 5000 Series CPU info and temperatures, support for CPU groups when retrieving per-core temperatures for Intel chipsets
Added a minimum size to the BurnInTest window so all UI elements can be accessed
Fixed a bug where USB3 low level errors would display an error message for the DX12 test rather than a information line for USB3 low level errors